Academia.edu no longer supports Internet Explorer.
To browse Academia.edu and the wider internet faster and more securely, please take a few seconds to upgrade your browser .
Enter the email address you signed up with and we'll email you a reset link.
- We're Hiring!
- Help Center
PDF DESIGN AND SIMULATION OF AN ENTERPRISE NETWORK USING PACKET TRACER: A Case Study of a Model Second… 55 Pages DESIGN AND SIMULATION OF AN ENTERPRISE NETWORK USING PACKET TRACER: A Case Study of a Model Secondary School DESIGN AND SIMULATION OF AN ENTERPRISE NETWORK USING PACKET TRACER: A C
Related Papers
IJIRST - International Journal for Innovative Research in Science and Technology
The purpose of this paper is to communicate between different Virtual-LANS and to learn more about VLAN Trunking and its operations. VLAN (virtual local area network) is used for configuring Layer-2 network. In this paper we have done an INTER-VLAN routing configured to connect different VLANs in a network whereas connecting in the same VLAN is also possible. INTER-VLAN ROUTING is also known as ROUTER-ON-A-STICK. Generally to communicate between two departments we need a Layer-3 device in place. Layer-3 switch is used on the network to configure INTER-VLAN routing without the need of a router. It is also configured to connect the different VLANS using some of the routing protocol, such as RIP and OSPF. We can also include a DHCP server in topology; the DHCP (dynamic host configuration protocol) is also invoked in this paper, to automatically configure an IP address for the each host. Application of this paper is enable a secure connection in the organization, such as information of higher level (management) is protected from the lower level (Workers) in an organization on a single network.
MARIE DIMANCHE
Daniel Gozalvez
ABDULRAZAQ BELLO
Introduction This guide is primarily about TCP/IP network protocols and ethernet network architectures, but also briefly describes other protocol suites, network architectures, and other significant areas of networking. This guide is written for all audiences, even those with little or no networking experience. It explains in simple terms the way networks are put together, and how data packages are sent between networks and subnets along with how data is routed to the internet. This document is broken into five main areas which are: 1. Basics-Explains the protocols and how they work together 2. Media-Describes the cabling and various media used to send data between multiple points of a network. 3. Architecture-Describes some popular network architectures. A network architecture refers to the physical layout (topology) of a network along with the physical transmission media (Type of wire, wireless, etc) and the data access method (OSI Layer 2). Includes ethernet, Token Ring, ARCnet, AppleTalk, and FDDI. This main area of the document can and should be skipped by those learning networking and read later. 4. Other Transport Protocols-Describes IPX/SPX, NetBEUI, and more. 5. Functions-Explains some of the functionality of networking such as routing, firewalls and DNS. 6. Further Details-Gives information about some protocols not covered in the "Basics" section. In the future, it will include more information about packet fragmentation and re-assembly along with more details about UDP and especially TCP and TCP connections. 7. More Complex functions-Documents multicasting, dynamic routing, and network management 8. Applications-Documents how some of the applications work such as ping and traceroute. In the future, it will cover telnet, Rlogin, and FTP. 9. Other Concerns-Includes installing drivers, network operating systems, applications, wide area networks, backing up the network and troubleshooting the network. 10. References-Includes a reference list of terms, RFCs and recommended reading. The reader may read this document in any order, but for beginners, it would be best to read through from the beginning with the exception of sections 2 (media), 3 (architecture), and 4 (other). At some point, however, the reader should be able to break from the basics and read about routing and IP masquerading.
Valentín Belisario Domínguez Vera
Numeric systems, Subnetwork fundamentals, Subnetting Exercises, Sistemas numéricos, fundamentos de subneteo, ejercicios de subneteo
Prasad Vasudewan
IRJET Journal
Today’s world is impossible without e-mails, online banking, chats and other important services provided by the internet. In this services computer network play very important role to exchange the information from one point to another .so we can say communication network, along with transportation networks, have become essential infrastructure in every society that allows the flow of people information and goods. For interconnectivity of components, network topology describe the physical and logical appearance and interconnection between arrangement of computers, cables and other component in a data communication network and how to be used for taking a packet from one device and sending it through the network to another device on a different network. . So in this paper, we are designing a network using a network simulator tool i.e. Cisco packet tracer, while keeping focus on bus, star, mesh topology to understand various concepts such as topology design, IP address configuration and how to send information in form of packet in a single network.
Petar Boyanov
Loading Preview
Sorry, preview is currently unavailable. You can download the paper by clicking the button above.
RELATED PAPERS
Neeraj Kumar
Sajjad bhatti
IOSR Journals
sangamesh k
Yaser Hemat
Olubunmi Fabiyi
Moumid Bouabid
Salim Zabir
albrian saputra
Munirawati 82
hari vashishtha
Bethel Mutanga
International Journal of Innovative Research in Science, Engineering and Technology
Obioma C Iwuamadi
Ceci Alvarez
IAEME Publication
Erik Guttman
Alejandro Barillas
Andres Dinamarca
International Journal of Recent Research Aspects ISSN 2349-7688
Tuyết Võ Ngọc
Ruri Hiromi
Paul Doolan
marina nashaat
- We're Hiring!
- Help Center
- Find new research papers in:
- Health Sciences
- Earth Sciences
- Cognitive Science
- Mathematics
- Computer Science
- Academia ©2024
- Engineering & Technology
- Electrical Engineering
- Telecommunications
Janitor_Jakab_Visual Learning - Packet Tracer case study
Related documents.
Add this document to collection(s)
You can add this document to your study collection(s)
Add this document to saved
You can add this document to your saved list
Suggest us how to improve StudyLib
(For complaints, use another form )
Input it if you want to receive answer
- Trending Now
- Foundational Courses
- Data Science
- Practice Problem
- Machine Learning
- System Design
- DevOps Tutorial
Router Configuration With Cisco Packet Tracer
In this network, a router and 2 PCs are used. Computers are connected with routers using a copper straight-through cable. After forming the network, to check network connectivity a simple PDU is transferred from PC0 to PC1. The network simulation status is successful. From this network, it can be observed that the router handles data transfers between multiple devices.
Step-1(Configuring Router1):
- Select the router and Open CLI.
- Press ENTER to start configuring Router1.
- Type enable to activate the privileged mode.
- Type config t(configure terminal) to access the configuration menu.
- Configure interfaces of Router1:
• Type interface FastEthernet0/0 to access FastEthernet0/0 and Configure the FastEthernet0/0 interface with the IP address 192.168.10.1 and Subnet mask 255.255.255.0. • Type interface FastEthernet0/1 to access GigabitEthernet0/0 and Configure the FastEthernet0/1 interface with IP address 192.168.20.1 and Subnet mask 255.255.255.0.
6. Type no shutdown to finish.
Router1 Command Line Interface:
Router>enable Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#interface FastEthernet0/0 Router(config-if)#ip address 192.168.10.1 255.255.255.0 Router(config-if)#no shutdown Router(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up Router(config-if)#interface FastEthernet0/1 Router(config-if)#ip address 192.168.20.1 255.255.255.0 Router(config-if)#no shutdown
Step-2(Configuring PCs):
- Assign IP Addresses to every PC in the network.
- Select the PC, Go to the desktop and select IP Configuration and assign an IP address, Default gateway, Subnet Mask
- Assign the default gateway of PC0 as 192.168.10.1.
- Assign the default gateway of PC1 as 192.168.20.1.
Step-3(Connecting PCs with Router):
- Connect FastEthernet0 port of PC0 with FastEthernet0/0 port of Router1 using a copper straight-through cable.
- Connect FastEthernet0 port of PC1 with FastEthernet0/1 port of Router1 using a copper straight-through cable.
Router Configuration Table:
Router1 | 192.168.10.1 | 255.255.255.0 | 192.168.20.1 | 255.255.255.0 |
PC Configuration Table:
PC 0 | 192.168.10.2 | 255.255.255.0 | 192.168.10.1 |
PC 1 | 192.168.20.2 | 255.255.255.0 | 192.168.20.1 |
Designed Network topology:
Simulation of Designed Network Topology:
Sending a PDU From PC0 to PC1:
Acknowledgment From PC1 to PC0:
Please Login to comment...
Similar reads.
- Computer Networks Quiz
- Cisco-packet-tracer
- California Lawmakers Pass Bill to Limit AI Replicas
- Best 10 IPTV Service Providers in Germany
- Python 3.13 Releases | Enhanced REPL for Developers
- IPTV Anbieter in Deutschland - Top IPTV Anbieter Abonnements
- Content Improvement League 2024: From Good To A Great Article
COMMENTS
Free online course to practice Internet of Things (IoT) skills in Cisco Packet Tracer, a virtual lab by Cisco Networking Academy. Sign up today!
Abstract and Figures. This paper relates the part of a cisco packet tracer for a case study to design and simulation virtual local area network. In this case study was carried out aimed at ...
Feb 13, 2020Knowledge. Author. Cisco Admin. Body. Hey guys, So I'm starting a new project called CopperPorts in order to help everybody train for their CCENT/CCNA the way I did. Here I post Packet Tracer scenarios on different exam topics. These scenarios are graded automatically as you solve them and they help you prepare and test your skills.
This paper relates the part of a cisco packet tracer for a case study to design and simulation virtual local area network. In this case study was carried out aimed at implement broadcast domains ...
Article Detail. The Cisco Learning Network. Certifications Help About Us. Cisco Learning Network Store Certification Tracker Cisco Learning Network Podcast. Stay Connected Member Directory.
This document summarizes a case study that used Cisco Packet Tracer to design and simulate a virtual local area network (VLAN). The case study implemented LAN switching using VLANs to break up broadcast domains and improve network performance. Cisco Packet Tracer allows students to create simulated networking environments to learn fundamental concepts like VLAN configuration and routing. It ...
logy and solving problems has greatly improved when students using the Cisco Packet Tracer [8]. Based on the related previous works, the effectiveness of using Cisco Packet Tracer as a learning tool in. omputer network course need to be investigated and routing protocol is chosen as a case study. As a lea.
PDF DESIGN AND SIMULATION OF AN ENTERPRISE NETWORK USING PACKET TRACER: A Case Study of a Model Second… 55 Pages DESIGN AND SIMULATION OF AN ENTERPRISE NETWORK USING PACKET TRACER: A Case Study of a Model Secondary School DESIGN AND SIMULATION OF ... So in this paper, we are designing a network using a network simulator tool i.e. Cisco packet ...
Cisco Networking Simplified (2nd Ed) (2008) - Free download as PDF File (.pdf), Text File (.txt) or read online for free. This document discusses a case study using Cisco Packet Tracer to design and simulate a virtual local area network (VLAN) with the goal of improving network performance. Cisco Packet Tracer allows students to experiment with network behaviors and configurations.
some aspects of a project. By nature, Packet Tracer prototypes are very inexpensive as it allows for testing projects that require complex network topologies. Also, Packet Tracer's Python support makes it easy to improve and eventually port any code to the actual devices when the testing phase is complete.
Step 1: Create a network topology in Cisco Packet Tracer with a router and multiple devices (e.g., PCs) connected to it. Use the "Router" device fr om the "Routers" category and "Generic PC ...
This document summarizes a research paper that presents a case study on designing and simulating a virtual local area network (VLAN) using Cisco Packet Tracer. The case study aims to implement LAN switching using VLAN to segment broadcast domains and improve network performance. Cisco Packet Tracer allows students to create simulated networks and experiment with concepts like VLANs. The ...
Packet Tracer is a free network simulator tool for certification exam preparation, particularly for CCNA students. It's available directly through the Cisco Networking Academy. Download and install the Packet Tracer software by signing up for the Introduction to Packet Tracer course, which teaches you the basics of using the tool. Download ...
Using Packet Tracer for CCNA Study (with Sample Lab) ... Packet Tracer and Alternative Lab Solutions. Number of Views 14.04K. Trending Articles. Cisco Packet Tracer: Software de Simulación para Redes; 200-301 CCNA Study Materials; Packet Tracer Labs; If you encounter a technical issue on the site, please open a support case. Follow Us ...
This study used two simulators to compare its effectiveness in assisting the students to learn computer networks and found that different effect of using Cisco Packet Tracer and GNS3, the average grade achievement in the class using G NS3 and using Cisco packet tracer were 76.67 and 70 respectively.
The Cisco Packet Tracer learning material was not fully accessible or even available, especially for the IoT section. In order to gather initial knowledge of the tool, and develop them by building the simulations, part of the thesis was to follow three online Cisco NetAcad course: Intro to IoT, Packet Tracer 1o1 (2016) and Packet Tracer 1o1 (2017).
VISUAL LEARNING: CASE STUDY OF CISCO NETWORKING ACADEMY'S PACKET TRACER 5.0 APPLICATION Jozef Janitor*, František Jakab** *Regional Cisco Networking Academy and Computer Networks Laboratory at Technical University of Košice, **Cisco Systems Slovakia, Bratislava [email protected], [email protected] 6th Int. Conference on Emerging e-learning Technologies and Applications Abstract.
The study concluded that the CISCO-packet-tracer simulator is an effective tool for fostering students' skills acquisition and comprehension of computer science concepts, while also recommending ...
Cisco Packet Tracer is a tool built by Cisco and it provides network simulation to practice simple and complex networks. The main purpose of the Cisco Packet Tracer is to help students learn the principles of networking and demonstrate the networking concepts. Step 1: Open the Cisco Packet Tracer. Step 2.: After opening the Cisco Packet tracer, add
Some useful labs for Cisco Packet Tracer. Unknown file type13 The Cisco Troubleshooting Methodology. Unknown file type. 13 The Cisco Troubleshooting Methodology. Download file 13 The Cisco Troubleshooting MethodologyDownload. Show more actions. Unknown file type14 Cisco Router and Switch Basics. Unknown file type.
Cisco Packet tracer is one such tool helps in better understanding about networking and its working is similar to real time. Its simulation based learning environment helps learners to critical thinking, troubleshooting ... A Case Study of Routing Protocol", International Journal of Information and Education Technology, Vol. 8, No. 1, January ...